[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[linrad] Re: Linrad new user



Hello Leif,

Well, Well! There is nothing like getting advice from the author of the software!! Thanks for answering.

Leif Asbrink wrote:


I have downloaded the software for LINRAD. I have scanned through the help file. I have attempted to run LINRAD and have entered some initial values in the setups. (They are probably wrong.)
If you can see and hear signals they are not "wrong" - but they could
be far from optimum for your purpose....
I don't see anything on the screen...no waterfall display or anything that indicates the program is running. At one point I did get a "SDR-14 detected" message.



I would like to have someone help me through the initial learning curve, if only to direct me to which articles I should read to begin with. The learning curve appears to be very steep to me at this point.
This seems to be a reasonable assumption;-)
To start with, it would be a good idea to master the SDR-14,
in other words to get an idea about what the AD6620 is doing.
I have used the SDR14 for over a year with the SpectraVue software and I am disappointed in the results. That is what led me to try Linrad. I am a retired electronics engineer and so I so have some understanding of FFT processes. However, I have never worked with them professionally and would not claim to know much about it.

In Linrad you have full freedom to select the decimation factors and to get various compromises between spur rejection and visible
bandwidth. For microwaves I guess spurs would not be any problöem at
all, and then you should look for a small value for RCF decimation.
Just play around with CIC2, CIC5 and RCF decimation to see what your computer can handle. The A/(D clock is 66.66666 MHz so you need
the product of all three decimation factors to be somewhere around
400 to 300 for a bandwidth between 166.66 kHz to 222.22 kHz.
Maybe you will find that CIC2=16, CIC5=10 and RCF=2 for a total
decimation of 320 and a sampling frequency of 208.33 kHz will be OK
for your computer. Most likely under Linux, but under Windows you
would probably have to use some more decimation.

This appears to be a good starting point for me. My computer is a dual CPU DELL XPS, about a year old.

On my computer, a 2.66 GHz PIV, the limit under Linux is about 230 kHz, but under Windows it is about 180 kHz.

Ok on this. I will look for this.

It will be a good idea to verify that Linrad does not fail when you
do other things that you intend to do on the same computer in case you
want to use it simultaneously for other purposes. This is more likely to
be a problem under Windows than under X11.

I run a logging program and an email program most of the time while I am at the radio. I don't think these two applications are too taxing on the CPU.

Once you have decided what bandwidth to go for, you should find a pulse
generator to do calibration. Read here:
http://www.sm5bsz.com/linuxdsp/flat/ampcal.htm
Actually this should not be required with an SDR-14 because the
filter response is exactly known since it is determined by the
digital filters (except for the small slope on gain vs frequency
that your converters may give) but because of my laziness, Linrad
does not know what filter response the digital filters inside
the AD6620 will supply so you will have to calibrate to get
an absolutely flat frequency response.

I have a test bench full of equipment good through 20 ghz, but I'm not sure any of it pulses :-)


Once you have a flat frequency response (after calibration) you
will find that a slower waterfall will supply better sensitivity.
The bin bandwidth as well as the averaging is important. I suggest
you start by getting a calibrated system at the bandwidth of your choice. The next step would be to decide whether to use the second FFT or not and that will depend on what you can observe with a calibrated system.

OK--Spectravue is the same...the larger the FFT sample size, the slower the waterfall and the more sensitive it is.

This mailing list is far from overloaded and your problem is the
same as many other operators face so I think it will be a good idea to discuss it on the list.

Wonderful! Thanks. I am leaving on a one week trip tomorrow and when I get back am leaving one day later to go the MUD (Microwave Update) in Pennsylvania. I will not have much time to experiment until after MUD. If all else fails, I have a CD with Ubuntu 7.04 and a friend who is really, really good with computers who will help me install it on my machine.

Thanks again, Leif. I will be continuing to work on Linrad as time allows. Being retired is very hard. There is so much to do and so little time.

73,

Dave, K4TO

#############################################################
This message is sent to you because you are subscribed to
 the mailing list <linrad@xxxxxxxxxxxxxxxxxxxxx>.
To unsubscribe, E-mail to: <linrad-off@xxxxxxxxxxxxxxxxxxxxx>
To switch to the DIGEST mode, E-mail to <linrad-digest@xxxxxxxxxxxxxxxxxxxxx>
To switch to the INDEX mode, E-mail to <linrad-index@xxxxxxxxxxxxxxxxxxxxx>
Send administrative queries to  <linrad-request@xxxxxxxxxxxxxxxxxxxxx>

LINRADDARNIL